Home > Unrecoverable Error > Unrecoverable Error In Scanner Code 31

Unrecoverable Error In Scanner Code 31

Check the wiring harness cable. Unrecoverable error - Error code 200 [ Home ] [ Join ] [ About ] [ Participants ] [ Community ] [ Statistics ] [ login/out ] Advanced Cancel the Personal Firewall of the client computer. Error 44 Defective font card installed in font slot. http://crimsonskysoftware.com/unrecoverable-error/unrecoverable-error-in-scanner.html

Los Altos Hills, CA Thank you. It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer. Permission to use this function has not been granted. Request Quote 947 Engine Board Engine board failure Replace the Engine Board Request Quote 953-954 NVRAM Failure NVRAM Failure 953: NVRAM Chip Failure 954: NVRAM CRC Failure Optra T 640/642/644

The pin should enter the tower on the HVPS and depress the cover switch. Yes, it likely is. rdybro Newbie Joined: Nov 3, 2015 Messages: 31 Thanks Received: 0 Trophy Points: 4 Location: Denmark Hi everyone. ERROR 22 The exit sensor was not unmade in time.

  • Regards, Rasmus rdybro, Apr 21, 2016 #1 hugovsky FreeNAS Experienced Joined: Dec 12, 2011 Messages: 469 Thanks Received: 48 Trophy Points: 26 Location: Portugal You should check your drives with
  • Error 7X Network Card Codes These user codes are documented in various network card user manuals.
  • Short self-test routine recommended polling time: ( 1) minutes.
  • An attempt was made to correct the error.
  • Bug628974 - ghostscript "Can't refill scanner input buffer!" error when converting eps to pdf Summary: ghostscript "Can't refill scanner input buffer!" error when converting eps to...
  • Additional info on X and XX codes available by email.
  • We got it this morning and I have it installed.

Conveyance self-test routine recommended polling time: ( 2) minutes. Uncle Fester's Basic FreeNAS 9.10 Configuration Guide FreeNAS 9.10.1-U2 SuperMicro SuperStorage Server 6047R-E1R36L (Motherboard: X9DRD-7LN4F-JBOD, Chassis: SuperChassis 847E16-R1K28LPB) 2 x Xeon E5-2670, 128 GB RAM, Chelsio T420E-CR Pool: 6 x 6 So don't, unless you're looking for learning experiences.Click to expand... This happens on Fedora 12 as well (ghostscript-8.71-6.fc12.x86_64), so I guess all branches are affected. --- Additional comment from rpm@greysector.net on 2010-08-25 18:38:10 EDT --- Created attachment 441067 [details] EPS file

Definitely--it's seen 59 C, which is way too high (back in my younger and dumber drives, I had a couple of drives in a server in my attic. Check paper sensor flag for restricted movement or damage. Check the fuser lamp is the correct type of lamp that should be installed. • Verify the line voltage is not exceeding the maximum rating for the printer. Stay logged in Sign up now!

The drive's a Seagate, and they report that field differently. Or can I get someone to email it to me? (curryfamily1 at yahoo.com) Also, would it help to delete all the .gz files? POR several times Check each board for secure ground. Make sure fuse is installed correctly, Verfy proper fuser is being used.

Lower the resolution. Error 920.X and 922.XX may display for a cold fuser. Check connecting cables for continuity. Error 47 47 Font Card Removed While Printing Printer needs data on removed card.

The maximum number of modes that can be stored is 100. check over here See TWAIN Driver help. Total time to complete Offline data collection: ( 89) seconds. Great - I thought so I've used a lot of time in here to find a great hardware-solution rdybro, Apr 21, 2016 #7 danb35 FreeNAS Expert Joined: Aug 16, 2011

Shop for Lexmark Maintenance kits * This is a model dependent interval Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits How did we do? Run the Quick Disk Test. now i\'ll have to wait another 24 hours to see if that worked... his comment is here Conveyance Self-test supported.

This website should be used for informational purposes only. If you have Telnet Error On G1 errors then we strongly recommend that you Download (Telnet Error On G1) Repair Tool. Once it finishes (likely in several hours), post the output of 'smartctl -x /dev/whatever' in code tags.

Is that the right command?

Fuser Pricing How did we do? Nothing jumps out as problematic, so I'll echo @Glorious1's question: are you sure you tested the right drive? Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 924 924 Fuser Error - Open circuit detected in thermistor circuit.

Members Online Now RodyMcAmp, 9C1 Newbee, Romualdas, Jon M, Dzerzhinsk, zfrank, vbGvMWpXht4kEm, TZAYUVAL, SweetAndLow Total: 148 (members: 9, guests: 130, robots: 9) Share This Page Tweet FreeNAS Community Home Forums > See "Connecting the Machine" "Using telnet", Network and System Settings Guide . Thank you and your firm again, you were terrific. http://crimsonskysoftware.com/unrecoverable-error/unrecoverable-error-exit-code-1.html This code is used by the vendor to identify the error caused.

Thanks for your help! Try opening Tray X. Regards rdybro, Apr 21, 2016 #3 danb35 FreeNAS Expert Joined: Aug 16, 2011 Messages: 4,018 Thanks Received: 951 Trophy Points: 111 Occupation: I have always been here.