I tried unplugging every other disk and every expansion card (save for the PCIe nVidia graphics which I kinda need ), and then I get this error. Ubuntu :: Extracting TGZ Files - Exit With Failure Status Fedora :: Evolution: Cannot Resolve Hostname - Open Calendar: Unexpected HTTP Status Programming :: Bash - Propogate Exit Status ? Some people use BOOTP to configure modules on the running plant, and it certainly works OK unless..... 1. I just checked the manuals and they are supported. http://crimsonskysoftware.com/unexpected-error/unexpected-error-status-1327.html
Adv Reply May 16th, 2011 #8 DanielBuus View Profile View Forum Posts Private Message Gee! Additional Information To check if the observed issue is as described above: Boot affected device with SLE11SP3 CD and run hardware report: # hwinfo > /tmp/hwinfo.txt Find hardware id and This update should only be applied if the symptoms above are being experienced, and are causing problems. A maintenance shell will now be started. http://www.backtrack-linux.org/forums/showthread.php?t=54546
Get the massage "Starting udev... PLCS.net - Interactive Q & A > PLCS.net - Interactive Q & A > LIVE PLC Questions And Answers > Problem to configure a IP address in a 1756-ENBT in a I have a redundant PLC system, each one with two EBNT card. I then wen to Rslinx / Rswho, found the card which was in slot #15 of the backplane.
Once the module reports that it is set up to its IP address, you can be assured that it will remember those settings, so just unplug it, and use it in like such....? Adv Reply May 16th, 2011 #3 DanielBuus View Profile View Forum Posts Private Message Gee! https://forums.suse.com/archive/index.php/t-5822.html I seem to have found dkms to be the source of the problem.
From there I re booted once more, and then everything was normal. Ubuntu :: Proto Not Found Error And Exit Status 127? Are you using nVidia, too? The firmware of the controller is 15.57.
Dec 14, 2010 I am using ubuntu server 10.10. http://www.plctalk.net/qanda/archive/index.php/t-77962.html I thought nouveau might still be loaded, so I tried adding "nouveau.blacklist=1" to GRUB_CMDLINE_LINUX_DEFAULT in /etc/default/grub and doing sudo update-grub2 to make sure that nouveau would be blacklisted by default, but But i guess this was for earlier versions of the ControlLogix Redundancy, am i right? And also try connecting to the processor using the RS-232 port and the driver RS-232 DF1 drivers, but experienced the same results.
udev loads with "ok" on a Dell 780. Check This Out This is what I getQuote:@XBMCLive:/home$ sudo apt-get remove openvpnReading package lists... In there, its says that we need to configure some Alias Topics and we need the "ControlLogix Redundancy Alias Topic Switcher" software. but i think that i have desobey the Contr_Conn recommendations.
I opted to install it and after installation when i select to run it, then all that is displayed in the picture occurs with the last line reading "unexpected error with Thanks. Provide Feedback © Micro Focus Careers Legal close Feedback Print Full Simple Request a Call Follow Us Facebook YouTube Twitter LinkedIn Newsletter Subscription RSS Home Skip Source browse to it - easy to say, but how? 1.
I kept getting this...[email protected]:~$ sudo apt-get install sametime-connect[sudo] password for rastlosen: Reading package lists... udev-work: '/sbin/modprobe -b pci:v00008086d00008C31sv00008086sd00002052bc0Csc03i30' unexpected exit with status 0x0009 ..." where the hardware ID belongs to USB 3.0 compatible controller. After performing system maintenance, press CONTROL-D to terminate the maintenance shell and restart the system. ... (warning).Give root password for maintenance(or type Control-D to continue): _For now, I just don't know
It is the latest? These Aren't Roasted! Reburned the iso onto a new disk2. Remember you can always "browse to" the module, across the backplane, from a processor's serial, or USB port.
And also try connecting to the processor using the RS-232 port and the driver RS-232 DF1 drivers. Ran the disk check from the CD and nothing out of the ordinary.I get the prompt screen with options to install, run without installing etc. Can you please make a step by step solution? have a peek here Wiki FAQ Advanced Search Forum PRODUCT RELATED DISCUSSIONS ENDPOINT MANAGEMENT ZENworks Configuration Management ZCM 11 ZCM11: Imaging ZCM 11.2.3 Imaging udev error You can view the discussions, but you must login
User contributions on this site are licensed under the Creative Commons Attribution Share Alike 4.0 International License. Blacklisting it will let you boot, using fallback framebuffer instead. showshockaOctober 31st, 2012, 10:36 AMI also ended up going into the BOOTP-DHCP Server in the Rockwell Software and putting in Subnet Mask 255.255.0.0 under Network Settings,went out of that and rebooted. View 2 Replies View Related Fedora :: Xoscope Error: Collect2: Ld Returned 1 Exit Status Sep 12, 2010 I am using a fully updated fedora 13 64-bit system and when i
Materials are provided for informational, personal or non-commercial use within your organization and are presented "AS IS" WITHOUT WARRANTY OF ANY KIND.